![]() The internal parts may make metallic noises with the change in temperature. A short time after use, I can hear a metallic sound. Some laundry starches and synthetic fibres may stick to the surface of the iron. Only spray starch on the reverse of the fabric to be ironed. Your iron is too hot, see our recommendations on temperature control settings in your product manual.The soleplate is dirty or brown and may stain clothing. Ensure that you have rinsed your clothes thoroughly in order to to remove soap deposits or chemicals from new garments which could stick to the iron. Your washing has not been rinsed sufficiently or you are ironing a new item of clothing before washing it.If this is the case, contact an approved service centre. You should never put these products in the water tank. You are using chemical descaling products or additives in the water.Brown streaks come out of the holes in the soleplate and stain the laundry. Some waterdrops could appeared underneath the ironing board and fall on the flooring. Your iron generates a lot of steam this steam is condensing on the board. Technical support Some waterdrops drip out onto the floor during ironing. When the anti-calc indicator blinks, perform the steps described in this video. Self-cleaning of the soleplate (depending on model):.Never hold the iron or its base unit under tap water.Ĭlean the plastic parts from time to time with a soft, slightly damp cloth. How do I maintain my steam generator properly?īefore cleaning, ensure that the appliance is unplugged and that the soleplate and iron rest plate are cold.ĭo not use any detergents or descaling products to clean the soleplate or base unit. Warning: The use of iron cleaner will cause damage to your soleplate's autoclean coating. It is recommended that you use a soft damp cloth on the warm soleplate, in order not to damage the surface. If cleaning dirt off is an issue, use the stick which is made specifically for cleaning the Durillium soleplates.Ĭlean the soleplate of your iron when it is cool with a damp cloth or a non-abrasive sponge. For easier, non-corrosive cleaning of your iron's soleplate, use a damp sponge on the soleplate while it is still warm. Regularly clean the soleplate with a damp, non metallic washing up pad. The next time you use your generator, press the "restart" button to turn off the orange "Anti-calc" light (depending on model). Models without scale collector: Rinse the boiler.Models with scale collector: Rinse the scale collector under water.Never use any descaling agent or vinegar when rinsing the boiler: they could damage it. ![]() Maintenance and cleaning How do I descale my steam generator?ĭescaling operation is not needed for the steam generator, nevertheless, you could rinse the boiler every 10 uses (refer to user manual). We recommend that you start with fabrics to be ironed at a low temperature. Important: The iron takes longer to cool down than to heat up. If ironing mixed-fibre fabrics, set the temperature for the most fragile fibre. We would advise ironing dark clothes inside out and using the correct temperature. Shiny marks can appear on some fabrics, especially on dark coloured fabrics. Never clean your iron's soleplate with abrasive or metallic pads.Avoid ironing over abrasive items (buttons, zip fastenings, etc.).Always place your iron on its heel rest or its base (depending on model).To avoid damaging the soleplate, follow this advice: How can I avoid scratching the soleplate of my iron? Note: Never use the vertical steam function on an item being worn by anyone. Press the steam control button intermittently and move the iron from top to bottom.Īs the steam produced is very hot, it softens the fibres and removes creases.Leave the item on a hanger and gently pull the fabric with one hand.To do this, set the iron temperature button to the maximum position. This function allows you to iron fabrics in situ or on a hanger. What is the vertical steam function used for? How do I use it? The ironing board cover should also be suitable to allow the flow of steam through. The board should be perforated to allow the steam to pass through the fibres of the fabric to soften it and make ironing easier. It should be steady and robust so that you can place the ironing appliance on it. How to better use my product What type of ironing board should I use?Ĭhoose a board that is height-adjustable to adjust it to your height. Find more detailed information in the Warranty section of the website.
0 Comments
Leave a Reply. |